[1]陈桂香,郭泽群,胡德平,等.承插型盘扣式钢管支架盘扣节点扭矩 - 转角模型适用性研究[J].西安建筑科技大学学报(自然科学版),2020,52(02):192-199,232.[doi:10.15986/j.1006-7930.2020.02.006]
　CHEN Guixiang,GUO Zequn,HU deping,et al.Study onapplicability of torque-rotation model of disk-pin joint node of disk lock steel tubular scaffold[J].J. Xi’an Univ. of Arch. & Tech.(Natural Science Edition),2020,52(02):192-199,232.[doi:10.15986/j.1006-7930.2020.02.006]
点击复制

承插型盘扣式钢管支架盘扣节点扭矩 - 转角模型适用性研究()
分享到：

西安建筑科技大学学报（自然科学版）[ISSN:1006-7930/CN:61-1295/TU]

卷:
52
期数:
2020年02期
页码:
192-199,232
栏目:
出版日期:
2020-04-25

文章信息/Info

Title:
Study onapplicability of torque-rotation model of disk-pin joint node of disk lock steel tubular scaffold
文章编号:
1006-7930(2020)02-0192-09
作者:
陈桂香1;  郭泽群1;  胡德平2; 徐 晨1
(1.河南工业大学 土木建筑学院, 河南 郑州 450001; 2.中铁十六局集团有限公司,北京 100000)
Author(s):
CHEN Guixiang1;  GUO Zequn1;  HU deping2;  XU Chen1
(1.College of Civil Engineering and Architecture, Henan University of Technology, Zhengzhou 450001, China; 2. China Railway 16th Bureau Group Co. Ltd., Beijing 100000, China)
关键词:
承插型盘扣式钢管支架;  盘扣节点;  扭矩 - 转角数学模型;  试验;  有限元数值计算
Keywords:
disk lock steel tubular scaffold;  disk-pin joint node;  torque-rotation mathematical model;  test;  Finite element analysis
分类号:
TU392.3
DOI:
10.15986/j.1006-7930.2020.02.006
文献标志码:
A
摘要:
承插型盘扣式钢管支架盘扣节点半刚性明显,是架体力学性能的重要影响因素之一.因此对架体进行精确数值分析时,需要合理选取盘扣节点扭矩 - 转角数学模型.在盘扣节点抗扭试验的基础上,采用数理统计方法获取盘扣节点扭矩 - 转角的二参数对数模型和三线性模型.通过架体荷载试验和有限元数值计算,对比分析盘扣节点单线性模型、三线性模型和二参数对数模型的适用性.三种盘扣节点模型参数选取合理时,架体有限元数值计算结果均可满足实际工程对稳定承载力的精度要求,其中盘扣节点采用二参数对数模型时,架体极限稳定承载力有限元数值计算值与试验值吻合性最好.由于立杆荷载分配不均、上下立杆连接半刚性、构件间隙和过盈装配等因素,架体侧移和盘扣节点扭矩的有限元数值计算值与试验值相差明显,结合试验数据规律,采用系数修正法对有限元数值计算结果进行了修正
Abstract:
The semi-rigidity of the disk-pin joint node of the disk lock steel tubular scaffold is obvious, which is one of the important factors affecting the mechanical properties of the frame. Therefore the reasonable selection of the torque-rotation angle mathematical model of the disk-pin joint node is the precondition of accurate numerical analysis of the frame. On the basis of the torsion test of the disk-pin joint node, the two-parameter logarithmic model and the trilinear model of the torque-rotation angle of the disk-pin joint node were obtained by mathematical statistics method. The applicability of single linear model, trilinear model and two-parameter logarithmic model was compared and analyzed by frame load test and finite element numerical calculation. The three kinds of disk-pin joint node models with reasonable parameters can satisfy the accuracy requirements of the stability bearing capacity of the practical engineering. When the two-parameter logarithmic model was adopted for the disk-pin joint node, the numerical calculation value of the ultimate stability bearing capacity of the frame was in the best agreement with the experimental value. Due to the uneven distribution of the load on the standing tube, the semi-rigid connection of the upper and lower standing tubes, the clearance and the interference fit, the calculated values of the lateral displacement of the frame and the torque of the disk-pin joint nodes are obviously different from the experimental values. The finite element calculation results were corrected by the coefficient correction method combined with the experimental data

参考文献/References:

[1] 郭正兴. 模板脚手架技术发展与展望[J]. 施工技术, 2018, 47(6): 79-83.
GUO zhenxing. Development and expectation of formwork scaffold technology[J]. Construction Technology, 2018, 47(6): 79-83.
[2] 陈安英,郭正兴,杨启龙. 承插型盘销式钢管支架结构稳定性试验与参数分析[J]. 施工技术, 2015, 44(14): 76-82.
CHEN anying, GUO zhenxing, YANG qilong. Structural stability test and parameter analysis of pin-disk type steel tubular scaffold [J]. Construction Technology, 2015, 44(14): 76-82.
[3] 肖明葵,徐灿,段军. 承插型盘扣式模板支撑体系盘扣节点半刚性研究[J]. 科学技术与工程, 2017, 17(12): 228-233.
XIAO mingkui, XU can, Duan Jun. Research on the semi-rigid joint of disk lock steel tubular type for support system [J]. Science Technology and Engineering, 2017, 17(12): 228-233.
[4] 中华人民共和国住房和城乡建设部.建筑施工临时支撑结构技术规范:JGJ300-2013[S].北京:中国建筑工业出版社,2013.
Ministry of housing and urban-rural development of P.P. China.Technical code for temporary support Structures in Construction: JGJ300-2013 [S]. Beijing: China Construction Industry Press, 2013.
[5] 中华人民共和国住房和城乡建设部.建筑施工承插型盘扣式钢管支架安全技术规程:JGJ231-2010[S].北京:中国建筑工业出版社,2010.
Ministry of housing and urban-rural development of P.P. China.Technical specification for safety of disk lock steel tubular scaffold in Construction: JGJ231-2010 [S]. Beijing: China Construction Industry Press, 2010.
[6] 闫雁军,陈鲁,张其林.插盘式脚手架实验研究及受力分析[J].施工技术, 2013, 42(14): 94-97.
YAN yanjun, CHEN lu, ZHANG qilin. Experimental study and parameter analysis on a disk-type steel scaffold [J]. Construction technology, 2013, 42(14): 94-97.
[7] 姜旭,张其林,顾明剑,等. 新型插盘式脚手架的试验和数值模型研究[J]. 土木工程学报, 2008, 41(7): 55-60.
JIANG xu, ZHANG qilin, GU mingjian, et al. Study of experimental and numerical model on a new disk-type steel scaffold [J]. China Civil Engineering Journal, 2008, 41(7): 55-60.
[8] 朱德春,蔡小华,何竞飞,等. 承插型盘扣式脚手架盘扣节点结构改进分析[J]. 建筑安全, 2016, 31(10): 21-25.
ZHU dechun, CAI xiaohua, HE jingfei,et al. Structural improvement analysis of the disk-pin joint node of disk lock steel tubular scaffold [J]. Construction Safety, 2016, 31(10): 21-25.
[9] 王晓光,段亚辉,尹汝琨. 盘扣式脚手架盘扣节点半刚性试验研究[J]. 建筑结构, 2015, 45(增刊): 1079-1082.
WANG Xiaoguang, DUAN Yahui, YIN Rukun. Experiment on socket plate fastener type scaffold characteristics of Semi-rigid node[J]. Building Structure, 2015, 45(S): 1079-1082.
[10]王洲春.承插型钢管脚手架实验研究[D].长沙:湖南大学,2013.
WANG zhouchun. The experimental investigation 0f socket type steel pipe scaffold[D]. Changsha: Hunan University, 2013.
[11]肖毅.新型盘式钢管脚手架的应用研究[D].昆明:昆明理工大学,2012
XIAO YI. Application research of new type ring scaffolding[D]. Kunming: Kunming University of Science & Technology, 2012.
[12]袁雪霞,金伟良,鲁征,等. 扣件式钢管支模架稳定承载能力研究[J]. 土木工程学报, 2006, 39(5): 43-50.
YUAN xuexiao, JIN weiliang, LU zheng, et al. A study on the stability bearing capacity of fastener-style tubular steel formwork-supports [J].China Civil Engineering Journal, 2006, 39(5): 43-50.

备注/Memo

备注/Memo:
收稿日期:2019-08-23 修改稿日期:2020-03-25
基金项目:河南省科技厅攻关项目(182107000007); 河南工业大学横向项目(ZZDT/SMWH-B/20171024)
第一作者:陈桂香(1976-),博士,教授,博士生导师,主要从事土木工程现代建造技术与管理.E-mail:chen-guixiang@163.com
更新日期/Last Update: 2020-04-25